Selection from the list of topics

?help

your basket basket(0)

display result tabledisplay mapSelect a result from the list by clicking on one of the table or map symbols.

add to basketIf you would like to display more than one table or map at once, add it to the basket by clicking on the basket symbol. Repeat this until all tables you are interested in are selected. Afterwards open the basket and choose show all.

Filter Results

You can further limit your Results with filters. Hoovering over the info symbol i will display additional information.
Remove the filter by clicking on the filter again.

Filter Results

Inventory

(1)
i
2018/26
show more...

Topic

(1)
i
Sum of the stem cross-sectional areas at a height of 1.3 m (level for measuring diameter at breast height [dbh]) of all living and dead trees and shrubs (standing and lying) with a dbh ≥12 cm. The total basal area corresponds to the sum of the basal area and the deadwood basal area.
show more...

Classification

(1)
i
Altitudinal vegetation belts in the system used in the guidelines for monitoring the sustainability and performance of protection forests (NaiS; Frehner et al. 2005) – in ten classes, whereby the classes «hyperinsubric», «colline» and «colline with beech» and «lower and upper montane» only occur in the Southern Alps (S), the classes «submontane», «lower montane», «upper montane» only in the Northern Alps (N) and the classes «high montane», «subalpine» and «upper subalpine» on both sides of the Alps. The information is based on the altitudinal vegetation belts determined by experts (accessible forest sample plots of NFI4 on the 1.4-km network; Arge Frehner et al. 2020), as well as on the altitudinal vegetation belts modelled for the period 1981-2010 (other sample plots; Zischg et al. 2021).
show more...

region

(1)
i
Demarcation of Switzerland into five regions (Jura, Plateau, Pre-Alps, Alps and Southern Alps) with relatively uniform growth and timber production conditions. The production regions were established by the Federal Office of Forestry long before the first National Forest Inventory (NFI1, 1983-1985). With a small exception along Lake Geneva, the boundaries of the production regions still follow the municipal boundaries of the time. Unlike the NFI, the Forestry Statistics of the Federal Statistical Office don't use the production regions as demarcation but rather the forestry zones, whose boundaries are somewhat different.
show more...

evaluation area

(1)
i
Forest that was less than two-thirds covered with shrubs in the five inventories NFI1 (1983-1985), NFI2 (1993-1995), NFI3 (2004-2006), NFI4 (2009-2017) and NFI5 (2018-2026) and was accessible on foot.
show more...

grid

(1)
i
Sub-grids 1, 2, 3, 4 and 5 of the field surveys on the sampling grid with a mesh size of 1.4 km (base grid).
search result: 1 entry on 1 page
LFI5 2018/26
production region
total basal area
altitudinal vegetation belts (NaiS; 10 classes)
accessible forest without shrub forest NFI1-NFI5
1.4 km grid, subgrids 1-5
search result: 1 entry on 1 page

Citation

Abegg, M.; Ahles, P.; Allgaier Leuch, B.; Cioldi, F.; Didion, M.; Düggelin, C.; Fischer, C.; Herold, A.; Meile, R.; Rohner, B.; Rösler, E.; Speich, S.; Temperli, C.; Traub, B.,
2023: Swiss national forest inventory NFI. Result tables and maps of the NFI surveys 1983–2022 (NFI1, NFI2, NFI3, NFI4, NFI5.1–5) on the internet. [Published online 30.05.2023] Available from the World Wide Web <http://www.lfi.ch/resultate/> . Birmensdorf, Swiss Federal Research Institute WSL
https://doi.org/10.21258/1769925