Selection from the list of topics

back

fellings #15
Stemwood volume of all trees and shrubs with a diameter at breast height (dbh) ≥12 cm with bark that were harvested between two inventories.

tree species (5 classes) #1157
Type of trees and shrubs ≥12 cm in diameter at breast height (dbh). The three most common species or species groups in Switzerland (spruce - Picea spp.; fir - Abies spp.; beech - Fagus sylvatica) are in individual classes, while the remaining species are classified as «other conifers» or «other broadleaves». Reference: Field Survey (MID 50: Baumart)

higher/lower altitude zone #2635
Areas in higher and lower altitude zones classified according to the system used for altitudinal vegetation belts in the guidelines for monitoring the sustainability and performance of protection forests (NaiS; Frehner et al. 2005). The boundary between the higher and lower altitudes runs between the «upper montane» and «lower montane» levels on the Northern Alps and between the «high montane» and «upper/lower montane» levels to the Southern Alps. The information is based on the altitudinal vegetation belts determined by experts (accessible forest sample plots of NFI4 on the 1.4-km network; Arge Frehner et al. 2020), as well as on the altitudinal vegetation belts modelled for the period 1981-2010 (other sample plots; Zischg et al. 2021).

production region #49
Demarcation of Switzerland into five regions (Jura, Plateau, Pre-Alps, Alps and Southern Alps) with relatively uniform growth and timber production conditions. The production regions were established by the Federal Office of Forestry long before the first National Forest Inventory (NFI1, 1983-1985). With a small exception along Lake Geneva, the boundaries of the production regions still follow the municipal boundaries of the time. Unlike the NFI, the Forestry Statistics of the Federal Statistical Office don't use the production regions as demarcation but rather the forestry zones, whose boundaries are somewhat different.

accessible forest without shrub forest NFI3/NFI4 #1429
Forest that was less than two-thirds covered with shrubs in both NFI3 (2004-2006) and NFI4 (2009-2017) and could be reached on foot.

1.4-km grid #410
NFI's sampling grid with a mesh size of 1.4 km. The 1.4-km grid is the grid size covering all the previous terrestrial Inventories, which is why it is also called the base grid.

Estimates and standard error of the estimates

The results published in the NFI tables are estimates for variables in the Swiss forest (population parameters) whose true values are not known and must therefore be extrapolated (estimated) from the NFI sample data.

The extrapolations carry uncertainties. However, the accuracy of the extrapolations can be reliably estimated from the NFI sample, which is designed to be a random sample. To this end, all NFI tables include a second figure in addition to the estimate itself, namely the standard error of the estimate.

In most tables the percent standard error is reported (±%), but the absolute standard error (±) is also reported occasionally, especially for estimated percentages. The relationship between absolute and percent standard error is as follows:

percent standard error = absolute standard error / estimate × 100

absolute standard error = percent standard error × estimate / 100

Information on the forest road network is based on a full survey of all forest roads. In this case, there is no need to specify a standard error because there is no uncertainty caused by sampling.

Confidence interval of the estimate

With the estimate and the standard error of the estimate, the limits of the so-called confidence interval of the estimate can be calculated as:

lower limit = estimate – tQ × absolute standard error

upper limit = estimate + tQ × absolute standard error

If the simple standard error is used for the calculation (tQ = 1), then the 68% confidence interval is formed. In this case, the true value of the population parameter has a 68% probability of lying within this confidence interval of the estimate. If the double standard error is used (tQ = 2), then there is a 95% probability that the true value lies within this 95% confidence interval.

Significance of the estimate

The confidence interval can be used to statistically test whether the estimated population parameter is larger or smaller than a specific reference or target value, or whether two estimated population parameters truly differ (in the real population). For practical applications, proceed as follows: if a reference value lies outside the confidence interval, the estimated population value can be interpreted as being significantly different from it; if it lies within the confidence interval, the difference between the estimated population parameter and the reference value can be interpreted as random or not significant. When two population parameters are compared, they can be interpreted as differing significantly if their confidence intervals do not overlap.

Dealing with missing values

When calculating a results table, data are not always available for all combinations of characteristics^* of the classification variables and regional demarcation applied. In most cases, this indicates that the attribute estimated with the respective target variable does not occur or occurs only very rarely. Usually, the value 0 is used (imputed). However, as this value is not based on direct measurements, the associated standard error is represented with a full stop [.]. If the imputed value of 0 is referred to in the calculation, e.g. in the case of percentages or certain change estimates, no value can be entered. In this case, the estimated value and standard error are both represented with a full stop [.].

For example, no Arolla pines have been found and measured in the Swiss Plateau to date (growing stock of Arolla pines by production region). The values can be assumed to be missing because Arolla pine does not occur in the Swiss Plateau and therefore the growing stock there must be 0.

^* e.g. ‘Arolla pine’ characteristic of the classification variable ‘tree species’ and ‘Swiss plateau’ characteristic of the ‘regional demarcation’

Changes

There are two types of changes in the NFI:

The first type involves specific target variables relating to components of change, such as increment, fellings, mortality and losses. These target variables are only available for two consecutive inventory cycles, e.g. NFI3–NFI4. In the evaluation of components of change, the classification variable characteristic of the second inventory cycle is assigned to the first inventory cycle. These evaluations therefore do not take into account potential changes in a classification variable characteristic from the earlier to the later inventory (e.g. from private to public ownership).

With the second type of change, the difference in target variables, such as number of stems, growing stock or forest area, is used to assess the change between two inventory cycles. Target variables are generally used to represent states, such as that in NFI4, but can also indicate the net change between any two inventory cycles, e.g. NFI1–NFI4. In evaluations of change using these target variables, the change in a classification variable characteristic is considered in the analysis. Consequently, one can detect, for example, that the forest area without shrub forest increased between the two inventory cycles. This only has an effect on classification variables whose characteristic (class) can actually change, e.g. the affiliation with a forest area or the tree condition.

NFI3–NFI4
fellings
tree species (5 classes) · higher/lower altitude zone
regional demarcation: production region
unit: 1000 m³/yr
evaluation area: accessible forest without shrub forest NFI3/NFI4
grid: 1.4-km grid
change 2004/06–2009/17
		production region
		Jura		Plateau		Pre-Alps		Alps		Southern Alps		Switzerland
tree species (5 classes)	higher/lower altitude zone	1000 m³/yr	±%	1000 m³/yr	±%	1000 m³/yr	±%	1000 m³/yr	±%	1000 m³/yr	±%	1000 m³/yr	±%
n/a	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	0	0	0	0	0	0	0	0	0	0	0	0
	higher altitude zone	0	0	0	0	0	0	0	0	0	0	0	0
	total	0	0	0	0	0	0	0	0	0	0	0	0
spruce	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	275	14	1440	7	366	16	52	27	14	90	2206	6
	higher altitude zone	255	16	15	54	645	13	555	13	48	45	1546	8
	total	534	11	1455	7	1011	10	608	12	62	40	3767	5
fir	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	267	18	474	12	293	16	10	50	0	0	1073	9
	higher altitude zone	100	18	1	100	233	17	34	32	2	71	387	12
	total	366	14	475	12	530	11	44	27	2	71	1475	7
other conifers	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	36	24	169	17	7	50	39	35	1	100	256	13
	higher altitude zone	0	0	0	.	0	0	117	19	11	58	125	18
	total	36	24	169	17	7	50	156	17	12	54	384	11
beech	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	280	12	562	10	182	20	95	30	0	100	1144	7
	higher altitude zone	65	22	6	82	30	27	9	43	0	0	119	16
	total	342	10	568	9	216	18	102	28	0	100	1284	6
other broadleaves	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	161	15	358	10	41	27	32	29	59	23	661	7
	higher altitude zone	6	46	0	0	32	29	13	49	1	100	53	22
	total	164	15	358	10	74	20	45	25	59	23	727	7
indeterminable	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	0	0	0	0	0	0	0	0	0	0	0	0
	higher altitude zone	0	0	0	.	0	0	0	0	0	0	0	0
	total	0	0	0	0	0	0	0	0	0	0	0	0
total	n/a	0	.	0	.	0	.	0	.	0	.	0	.
	lower altitude zone	1019	9	3002	5	889	11	229	20	74	25	5341	4
	higher altitude zone	426	12	22	46	940	11	729	12	61	37	2231	7
	total	1442	7	3024	5	1838	8	955	10	136	22	7636	3

Table citation

Abegg, M.; Ahles, P.; Allgaier Leuch, B.; Cioldi, F.; Didion, M.; Düggelin, C.; Fischer, C.; Herold, A.; Meile, R.; Rohner, B.; Rösler, E.; Speich, S.; Temperli, C.; Traub, B.,
2023: Swiss national forest inventory - Result table No. 1266076. Birmensdorf, Swiss Federal Research Institute WSL

back