Selection from the list of topics

back

NFI4
volume of bole wood (HG 2010)
timber assortment classes (HG 2010) · conifers and broadleaves
unit of reference: production region
unit: 1000 m³
unit of evaluation: accessible forest without shrub forest NFI3/NFI4
grid: 1.4 x 1.4 km grid
state2009/17
		production region
		Jura		Plateau		Pre-Alps		Alps		Southern Alps		Switzerland
timber assortment classes (HG 2010)	conifers and broadleaves	1000 m³	± %	1000 m³	± %	1000 m³	± %	1000 m³	± %	1000 m³	± %	1000 m³	± %
small diameter timber	conifers	3573	6	2016	7	1743	8	1307	5	145	7	8783	3
	broadleaves	123	4	119	4	83	6	75	7	108	5	507	2
	total	3696	6	2135	7	1826	8	1381	4	253	4	9291	3
classes 1 and 2	conifers	8782	4	13232	4	18704	3	33028	2	5286	6	79031	2
	broadleaves	10330	4	10921	4	7756	5	7338	5	9574	4	45919	2
	total	19112	3	24153	3	26459	3	40366	2	14860	3	124950	1
classes 3 and 4	conifers	18649	4	20268	4	32411	3	40433	2	6881	6	118642	1
	broadleaves	15051	3	16137	4	9597	5	5331	7	4395	6	50511	2
	total	33700	2	36406	2	42008	2	45764	2	11276	4	169153	1
classes 5 and 6	conifers	4353	8	5192	7	11639	5	14296	4	3307	9	38787	3
	broadleaves	3391	9	6648	7	2616	10	1253	12	1689	16	15596	4
	total	7744	6	11839	5	14255	4	15550	4	4996	8	54384	2
total	conifers	35357	3	40708	3	64497	3	89063	2	15618	5	245244	1
	broadleaves	28895	3	33824	3	20051	4	13998	5	15766	4	112534	2
	total	64253	2	74532	2	84548	2	103061	2	31384	3	357778	1

volume of bolewood (HG 2010) #211
Holzvolumen des Schaftes ohne Rinde und ohne Stock von mindestens 7 cm Durchmesser (Derbholzgrenze) aller Bäume und Sträucher ab 12 cm Brusthöhendurchmesser (BHD), ermittelt mit den Schaftform-Funktionen gemäss Kaufmann (2001). Die Definition der Sortimente erfolgte nach den Handelsgebräuchen Ausgabe 2010.
timber assortment classes #1788
Durchmessersortierung des Rundholzes in vier Klassen anhand der Schweizer Handelsgebräuche für Rohholz, Ausgaben 2010 und 2021 (HG 2010). Dabei werden die Klassen 1 und 2, 3 und 4 sowie 5 und 6 der HG 2010 je zu einer Klasse zusammengefasst.
conifers and broadleaves #96
Art der Bäume und Sträucher ab 12 cm Brusthöhendurchmesser (BHD) in zwei Klassen (Nadelholz, Laubholz). Grundlage: Feldaufnahme (MID 50: Baumart)
production region #49
Die Produktionsregionen sind Regionen mit ähnlichen forstlichen Wuchs- und Produktionsbedingungen, erstellt durch das damalige Bundesamt für Forstwesen für die forstliche Statistik lange vor dem ersten LFI (1983-85). Die Regionenzugehörigkeit wurde definiert über die damaligen Gemeindegrenzen nach unbekannten Kriterien. Das LFI arbeitet sei jeher mit diesen unveränderten Perimetern mit einer winzigen kleinen Ausnahme am Genfersee. In der heutigen Forststatistik (Bundesamt für Statistik, BFS) hat der Begriff Produktionsregionen in «Forstzonen» gewechselt. Diese Regionen werden vom BFS unterhalten und dabei fanden Änderungen statt. Dabei wurde vermehrt auf die Lage des Waldes innerhalb einer Gemeinde Rücksicht genommen. Für einige Gemeinden entlang des Jurabogens bedeutet dies beispielsweise, dass sie neu der Forstzone «Jura» angehören und nicht wie bisher (Produktionsregionen) dem Mittelland. Das LFI hat die alten Perimeter beibehalten, die sich heute mit diversen neuen Gemeindegrenzen nicht mehr decken.
accessible forest without shrub forest NFI3/NFI4 #1429
Wald, der sowohl im LFI3 (2004-2006) als auch im LFI4 (2009-2017) zu weniger als zwei Dritteln mit Sträuchern bedeckt war und zu Fuss aufgesucht werden konnte.
1.4 x 1.4 km grid #410
Stichprobennetz des LFI mit einer Maschenweite von 1,4 km. Beim 1,4-km-Netz handelt es sich um das gemeinsame Netz aller bisherigen terrestrischen Inventuren, weshalb es auch als Basisnetz bezeichnet wird.

Estimates and standard error of the estimates

The results published in the NFI tables are estimates for variables in the Swiss forest (population parameters) whose true values are not known and must therefore be extrapolated (estimated) from the NFI sample data.

The extrapolations carry uncertainties. However, the accuracy of the extrapolations can be reliably estimated from the NFI sample, which is designed to be a random sample. To this end, all NFI tables include a second figure in addition to the estimate itself, namely the standard error of the estimate.

In most tables the percent standard error is reported (±%), but the absolute standard error (±) is also reported occasionally, especially for estimated percentages. The relationship between absolute and percent standard error is as follows:

percent standard error = absolute standard error / estimate × 100

absolute standard error = percent standard error × estimate / 100

Information on the forest road network is based on a full survey of all forest roads. In this case, there is no need to specify a standard error because there is no uncertainty caused by sampling.
Confidence interval of the estimate

With the estimate and the standard error of the estimate, the limits of the so-called confidence interval of the estimate can be calculated as:

lower limit = estimate – tQ × absolute standard error

upper limit = estimate + tQ × absolute standard error

If the simple standard error is used for the calculation (tQ = 1), then the 68% confidence interval is formed. In this case, the true value of the population parameter has a 68% probability of lying within this confidence interval of the estimate. If the double standard error is used (tQ = 2), then there is a 95% probability that the true value lies within this 95% confidence interval.
Significance of the estimate

The confidence interval can be used to statistically test whether the estimated population parameter is larger or smaller than a specific reference or target value, or whether two estimated population parameters truly differ (in the real population). For practical applications, proceed as follows: if a reference value lies outside the confidence interval, the estimated population value can be interpreted as being significantly different from it; if it lies within the confidence interval, the difference between the estimated population parameter and the reference value can be interpreted as random or not significant. When two population parameters are compared, they can be interpreted as differing significantly if their confidence intervals do not overlap.
Dealing with missing values

When calculating a results table, data are not always available for all combinations of characteristics^* of the classification variables and regional demarcation applied. In most cases, this indicates that the attribute estimated with the respective target variable does not occur or occurs only very rarely. Usually, the value 0 is used (imputed). However, as this value is not based on direct measurements, the associated standard error is represented with a full stop [.]. If the imputed value of 0 is referred to in the calculation, e.g. in the case of percentages or certain change estimates, no value can be entered. In this case, the estimated value and standard error are both represented with a full stop [.].

For example, no Arolla pines have been found and measured in the Swiss Plateau to date (growing stock of Arolla pines by production region). The values can be assumed to be missing because Arolla pine does not occur in the Swiss Plateau and therefore the growing stock there must be 0.

^* e.g. ‘Arolla pine’ characteristic of the classification variable ‘tree species’ and ‘Swiss plateau’ characteristic of the ‘regional demarcation’
Changes

There are two types of changes in the NFI:

The first type involves specific target variables relating to components of change, such as increment, fellings, mortality and losses. These target variables are only available for two consecutive inventory cycles, e.g. NFI3–NFI4. In the evaluation of components of change, the classification variable characteristic of the second inventory cycle is assigned to the first inventory cycle. These evaluations therefore do not take into account potential changes in a classification variable characteristic from the earlier to the later inventory (e.g. from private to public ownership).

With the second type of change, the difference in target variables, such as number of stems, growing stock or forest area, is used to assess the change between two inventory cycles. Target variables are generally used to represent states, such as that in NFI4, but can also indicate the net change between any two inventory cycles, e.g. NFI1–NFI4. In evaluations of change using these target variables, the change in a classification variable characteristic is considered in the analysis. Consequently, one can detect, for example, that the forest area without shrub forest increased between the two inventory cycles. This only has an effect on classification variables whose characteristic (class) can actually change, e.g. the affiliation with a forest area or the tree condition.

Table citation

Abegg, M.; Brändli, U.-B.; Cioldi, F.; Fischer, C.; Herold, A.; Meile, R.; Rösler, E.; Speich, S.; Traub, B., 2020: Swiss national forest inventory - Result table No. 806576. Birmensdorf, Swiss Federal Research Institute WSL
https://doi.org/10.21258/1718541

back

Selection from the list of topics

Estimates and standard error of the estimates

Confidence interval of the estimate

Significance of the estimate

Dealing with missing values

Changes

Table citation